v2rayN Avalonia vs. WPF: Which Windows Version Should You Install?

Compare v2rayN Avalonia and WPF for platform support, interface, and features, with download recommendations for Windows, macOS, and Linux.

At a glance

For a first install on Windows x64, start with the Avalonia version labeled Desktop. If your WPF setup is familiar and stable, there’s no need to switch just for a different interface. Choose Avalonia for macOS or Linux, and check your processor architecture and package format. After switching, test the local proxy first, then check system proxy and routing settings. Don’t mistake configuration differences for framework differences.

Windows x64: Desktop or WPF?

Desktop and WPF on the download page refer to two desktop interfaces, not two proxy protocols. The Avalonia interface runs on multiple desktop platforms, while WPF retains the classic Windows interface. Menus, tray behavior, list controls, and scaling may differ between versions. Even when settings have similar names, don’t expect buttons to match screenshots from the other version pixel for pixel.

Avalonia (Desktop)

Recommended

For your first install, start with the Desktop version. If you also use a Mac or Linux PC, one familiar interface can make things easier. System proxy settings and permissions still need to be configured separately on each platform.

Best for: first-time Windows x64 installs and use across desktop platforms

WPF

If you’re happy with the current version’s tray controls, keyboard shortcuts, and display scaling, keeping the familiar interface is easier than switching and troubleshooting your configuration again.

Best for: stable existing setups and users who prefer the classic Windows interface

In Windows, open Settings → System → About and check System type. Don’t rely on “64-bit” alone: x64 and ARM-based processors use different architectures. The Windows download listed here is for x64. Whether it runs as expected on an ARM device depends on system compatibility and the version’s requirements. If startup reports a missing runtime, note the component named in the error and check the instructions for your download. There’s no need to reinstall both interfaces on a guess.

macOS and Linux: Choose by architecture and package format

Use Avalonia on both platforms, but check different things before installing

macOS: Check the chip first
  • In About This Mac, check Chip or Processor. Choose arm64 for Apple silicon and x64 for an Intel processor.
  • The corresponding download is a DMG. After installation, make sure the client starts, then check that your active network service is using the proxy settings.
Linux: Check your distribution and system architecture
  • Debian and Ubuntu users usually want DEB. For Fedora and other RPM-based distributions, choose RPM and check the release notes for dependencies.
  • uname -m returns x86_64 for x64 and aarch64 for arm64. Also make sure the package architecture matches your system’s user space.

Cross-platform means the interface runs on different operating systems; it doesn’t mean one installer works everywhere.

Desktop proxy settings on Linux don’t apply to every app. A graphical browser, terminal tool, and background service may each read different proxy settings. If the browser works but the terminal doesn’t, check which settings the terminal tool actually uses. On macOS, distinguish the system proxy from proxy settings configured directly in an app. If behavior changes when switching between Wi-Fi and Ethernet, check the active network service rather than relying only on the client window’s status.

Features and performance: Separate the interface, core, and traffic entry point

The interface is used to edit settings, manage subscriptions, and view logs. The selected core, such as Xray, handles proxy connections. To compare features, note the client and core versions on both sides, then check the active configuration, routing mode, and traffic entry point. If the two packages have different versions, a missing button alone won’t tell you which framework supports a feature. System proxy and Tun are also different entry points: the former depends on apps using the system proxy settings, while the latter involves a virtual interface, platform permissions, and routing changes.

127.0.0.1
Loopback address example
10808
Example local proxy port; use the value in your settings

After switching, test the local proxy before enabling the system proxy

In the client, open Settings → Parameter settings and check the local listener. Then point an app that supports manual proxy settings to that address and port. Make sure the proxy type matches the actual inbound protocol: for example, if the configuration only provides SOCKS, don’t enter the same port as an HTTP proxy. If manual proxying works but enabling the system proxy causes problems, first check whether the app uses the system settings.

To compare speed, use the same computer, connection profile, core and version, and test destination. Run only one client at a time. Memory usage for the interface process in Task Manager, response time when clicking a list, and actual download throughput are different metrics. A single download fluctuation doesn’t prove one interface is faster. If only window interactions feel sluggish, check high-DPI scaling and scrolling through long lists separately; don’t change proxy settings at the same time.

Switching from WPF to Avalonia: Backup and verification steps

  1. Record the old setup. Note the client and core versions, selected configuration, subscription groups, custom routes, local port, and system proxy status. Use the export feature available in your current version, if there is one. Also back up the data directory the old version actually uses; don’t assume it’s the installation directory. Subscription URLs may contain access credentials, so store them somewhere you control.
  2. Exit the old version before launching the new one. Quit the old client from the system tray; closing just the main window may leave it running. If both processes use the same local port, the new version may fail to listen. Even with different ports, having both versions modify the system proxy makes troubleshooting harder. On the new version’s first launch, don’t let it take over traffic automatically.
  3. Import using a method supported by the new version. See the import instructions in the quick start guide. Restore a commonly used configuration or a subscription group first, then add custom rules. A successful subscription update only confirms that the list was retrieved; it doesn’t mean your local routing, ports, or selected items were restored. When migrating between versions, don’t overwrite the new version’s entire configuration directory.
  4. Check each item and keep a rollback path. Check the core startup log first, then test the local proxy, and finally enable the system proxy. If you used Tun, test it separately at the end. To roll back, disable any traffic interception features enabled in the new version and quit it before restoring the old version. If the network still doesn’t work, check whether the system proxy points to a local port that’s no longer listening.

Choosing a version and switching: FAQs

Can I install both versions on one Windows PC?

You can keep both versions for comparison, but check where each stores its data. Different installation directories don’t necessarily mean their settings are isolated. When trying them out, disable startup on one version and quit it from the tray before launching the other.

The new version shows my servers, but websites won’t load in the browser. What should I do?

First, check the log to confirm the core started and didn’t fail to listen. Then check whether the browser follows the system proxy, uses manual settings, or has an extension overriding them. If it still points to the old port, change it to the port the new version is actually listening on and make sure the proxy protocol matches.

Why is routing different even though my subscription is still there?

Check the active routing configuration, rule order, and default outbound first. Then make sure the app is actually sending traffic through the local proxy. A subscription’s server list is separate from custom routes saved in the client. See the routing configuration reference to check each item.

The Linux package installed. Why can’t I find the tray icon?

Reopen the main window from the applications menu and check whether the process is running. If the window works but there’s no tray entry, check whether your desktop environment supports and has enabled status icons. While troubleshooting, don’t rely on the tray icon to quit the app, and don’t assume a missing icon means the core failed to start.

Download v2rayNCompare platforms and packages